Skip to content

Hot and Chilled Water Pipework Systems

Key Areas
Course Content
Learning Outcomes
Who Should Attend
Course Fees
Getting Setup
How to Purchase 

 

Purchase Hot & Chilled Water Pipework Systems Now


Key Areas

The aim of the module is to prepare engineers for the process of designing a complete pipe-work system for delivering heating or chilled water to terminal units in buildings. These types of system typically distribute heating or cooling water to radiators, fan coil units, chilled beams, radiant panels or chilled ceilings.

The module is primarily intended for junior to intermediate engineers who are being asked to design a system for the first time.  However, the module is not for the complete beginner. There's an assumption from the outset that the user will have completed a college or university course on mechanical engineering, or possibly a course on building services engineering, and so will have some understanding of the basic fluid dynamic principles that underlie system design. They will also have access to the support of a more senior engineer within their organisation who can guide them on the procedures and protocols for completing design drawings and specification documents.

Furthermore, the module does not explain how to design a complete heating or cooling system.  There is an assumption that heating and cooling loads have already been determined - based on building heat loss and heat gain calculations - and that, using the results of those calculations, the heating and cooling emitters have already been sized and their design flow rates specified based on whatever design temperature differential has been selected. 

The module therefore deals with how to size the pipes, pumps and valves, how to layout the system and how to control its operation.

This course is worth 7 CPD hours


Course Content 

  • Welcome
  • Introduction
  • Sizing pipes and calculating system pressure losses
    • Pipe sizing and selection
    • Velocity limits
    • CIBSE Guide C4
    • Calculating maximum system pressure loss
    • Pipe materials
    • Pump sizing and selection
    • Activity
  • Valves
    • Valves
    • Flow regulations
    • Control valves
    • Activity                                 
  • Features to facilitate pre-commissioning cleaning                                           
  • System design
    • System design
    • DPCV controlled 
    • PICV controlled
    • Module controlled
    • Activity 
  • Conclusion


Learning Outcomes 

  • Size and select the pipe-work
  • Size and select the system pumps
  • Recognise alternative valve types
  • Plan for pre-commission cleaning
  • Design a complete system
  • (Primary and secondary circuits)


Who Should Attend

CIBSE online learning courses are suitable for those wishing to enhance and support their current knowledge base, as well as graduates within an engineering discipline. 

Each unit has been peer reviewed and tested through this group. The units allow students to take a coordinated journey through an individual topic or a series of topics. The units form the backbone of several corporate training schemes.


Course Fees 

  • Membership Rate: £270 (324 inc VAT)
  • Standard Rate: £300 (£360 inc VAT) 

 

Getting Setup


New User
If you are a new user to CIBSE and would like to purchase an online learning course please contact us on 020 8772 3660 or email us at onlinelearning@cibse.org to get you started. 

Alternatively, please follow the set up instructions below:
To set up the MyCIBSE Portal create a username from your desired email address and create a password. Then login to the Online Learning Portal with the same credentials as used to create your MyCIBSE Portal.

Once you have successfully logged in to both portals, please contact us on 020 8772 3660 or email us at onlinelearning@cibse.org to activate your account.


Existing User
If you are already a user of MyCIBSE but have not yet accessed our Online Learning Portal, please login to the Online Learning Portal with the same credentials as used for your MyCIBSE Portal. 

Once you have successfully logged in, please contact us on 020 8772 3660 or email us at onlinelearning@cibse.org to activate your account.



How to Purchase

  • ​Online: Log into your MyCIBSE account to purchase your desired course. Courses can be purchased by selecting the tab 'Online Learning' then by finding your course under one of the three topics mentioned above. This is by method of Credit / Debit card only.

  • For corporate rates please contact the training team on onlinelearning@cibse.org



Corporate subscribers, please contact the training team at onlinelearning@cibse.org